The I|Flux: 5 Elite uses an appropriate filter arrangement with 286 square feet of surface area – double that of a typical 5HP collector. To do this, we used a smaller diameter bag and a lot more of them. This arrangement maximizes the amount of surface area possible which is vital to adequate airflow through the collector. Keeping these filters clean was addressed in the design.
+$699 Freight
The 12″ inlet has a net airflow of 3991CFM with a static pressure of 5″wc. A typical CNC Router needs a minimum requirement of 1500CFM, while a typical 37″ wide belt sander would call for a minimum 2000CFM. This makes the I|Flux: 5 Elite a great fit for a CNC Router-based cabinet shop that would be running several tools at once.
With fine dust, the key is to have a large filter surface area and to keep those filters clean. The smaller tube filter design of the iFlux|5 Elite are designed for the fine dust to cake on and the inner side of the filters and fall down into the bin as the mass grows. The filter surface area of the iFlux |5 Elite is 286 square feet. A typical 5HP dust collector has a surface area of 150 square feet. This increase in filter area translates to a large increase in airflow, making the iFlux an ideal machine for fine dust applications.
Bins Changing the waste bins has never been easier. Deactivate the air-tight seal by pulling up the release bar and rolling out the bin. The positive pressure design means there is no need for a bag hold-down system like in a multi-stage system. The wheels swivel 360 degrees and are mounted on a sturdy base to ensure they work in your shop for many years.
The I|Flux:5 Elite fine dust collector displays an amperage readout on the control panel. This allows the user to monitor the efficiency of the motor. A high-frequency remote is also included so the operator can turn the machine on and off within a 60-meter range.
There are several NFPA standards in place to ensure the proper installation and use of a dust collector. For woodworkers, the standard is NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities. The I|Flux: 5 Elite complies directly with this standard. In addition, the I|Flux is fitted with a phase controller and TEFC motor for added electrical safety.
Power Requirements: 220V/ 60Hz/ 3ph
Amperage: 14.4 Amps
Floor Space (W x L): 8.2′ x 3.74′
Machine Weight: 606.3 lbs (275 kgs)
Motor HP: 5
Motor RPM: 1720
Air Flow: 3991CFM @ 5″wc
Inlet Diameter: 12″
Filter Area: 286.3 ft²
Filter Bag (L x D x H): 28 x 168 x 1800mm
Filter Bag Material: Polyester
Filter Cleaning: Manual Shaker
Waste Bin: EZ-lift Metal Bin 64 gal x 2
Shipping Weight: 723 lbs (328 kgs)
Shipping Dimensions (L x W x H): 75″ x 39″ x 80″
The 15″ inlet has a net airflow of 5000CFM with a static pressure of 6″wc. A typical CNC Router needs a minimum requirement of 1500CFM, while a typical 37″ wide belt sander would call for a minimum 2000CFM. This makes the I|Flux: 5 Elite a great fit for a CNC Router-based cabinet shop that would be running several tools at once.
With fine dust, the key is to have a large filter surface area and to keep those filters clean. The smaller tube filter design of the I|Flux:5 Elite is designed for the fine dust to cake on the inner side of the filters and fall into the bin as the mass grows. The filter surface area of the I|Flux: 5 Elite is 409 square feet. A typical 5HP dust collector has a surface area of 260 square feet. This increase in filter area translates to a large increase in airflow, making the I|Flux an ideal machine for fine dust applications.
Bins Changing the waste bins has never been easier. Deactivate the air-tight seal by pulling up the release bar and rolling out the bin. The positive pressure design means there is no need for a bag hold-down system like in a multi-stage system. The wheels swivel 360 degrees and are mounted on a sturdy base to ensure they work in your shop for many years.
The I|Flux:5 Elite fine dust collector displays an amperage readout on the control panel. This allows the user to monitor the efficiency of the motor. A high-frequency remote is also included so the operator can turn the machine on and off within a 60-meter range.
There are several NFPA standards in place to ensure the proper installation and use of a dust collector. For woodworkers, the standard is NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities. The I|Flux: 5 Elite complies directly with this standard. In addition, the I|Flux is fitted with a phase controller and TEFC motor for added electrical safety.
Power Requirements: 220V/ 60Hz/ 3ph
Amperage: 14.4 Amps
Floor Space (W x L): 8.2′ x 3.74′
Machine Weight: 606.3 lbs (275 kgs)
Motor HP: 5
Motor RPM: 1720
Air Flow: 3991CFM @ 5″wc
Inlet Diameter: 12″
Filter Area: 286.3 ft²
Filter Bag (L x D x H): 28 x 168 x 1800mm
Filter Bag Material: Polyester
Filter Cleaning: Manual Shaker
Waste Bin: EZ-lift Metal Bin 64 gal x 2
Shipping Weight: 723 lbs (328 kgs)
Shipping Dimensions (L x W x H): 75″ x 39″ x 80″
Complete this short form &
a Laguna Representative Will Contact You Shortly
I|Flux: 5 Manual